- Airship Service MZ-600ME
The airship is equipped with an automatic flight control system without a pilot as well as using GPS. The system provides services as a remote monitoring platform and a data collection center.
- Aerostat S-3M
The aerostat is equipped with a load system such as a camera with GPS to be used as a remote monitoring platform system.
Structural and Mechanics
- Metallographic Examination
A specimen preparation process for microscopic examination and micro structure study of material physical characteristic.
- Static Tensile Testing
Static tension test to determine mechanical properties of material.
- Dynamic Tensile Testing
Recurring tension test to determine fatigue properties of material.
- Micro Hardness Testing
To determine hardness of material (10 – 1000gf).
- Macro Hardness Testing
To determine hardness of material (1kgf – 120kg).
- SEM-EDX Examination
Material science analysis to determine micro structure, morphology and elements.
- Bend Test
Test to determine the ductility of material.
- Compression Test
To determine mechanical properties of material.
- 3D Infinite Focus Microscope Examination
3D surface analysis and morphology measurement.
- Charpy Impact Testing
Test to determine strength of material.
- Distillation at Atmospheric Pressure
To determine quantitatively the boiling range characteristics of petroleum products using automated distillation apparatus.
- Dropping Point
To determine the dropping point of lubricating grease.
- Flash Point by Pensky Martens Closed Cup Tester
To determine the flash point of petroleum products in the temperature range from 40 to 370°C using an automated Pensky Martens closed-cup apparatus.
- Corrosiveness to Copper from Petroleum Products by Copper Strip Test
To determine the corrosiveness to copper of aviation turbine fuel having a vapor ressure no greater than 124kPa (18psi) at 37.8°C.
- Density of Liquids by Digital Density Meter
To determine the density, relative density and API Gravity of petroleum distillates and viscous oils that can be handled in a normal fashion as liquids at the temperature of test using automated sample injection equipment.
- Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and Calculation of Kinematic Viscosity)
To determine concurrent measurement of both the dynamic viscosity and the density of liquid petroleum products and crude oils, both transparent and opaque.
- Flash Point by Abel Closed Cup
To determine the flash point of petroleum products in the temperature range from -5 to 66.5°C using an automated Abel closed-cup apparatus.
- Electrical Conductivity
To determine the electrical conductivity of aviation and distillate fuels with and without a static dissipator additive.
- Measurement of Fuel System Icing Inhibitors (Ether Type)
To measure the concentration of Diethylene Glycol Monomethyl Ether (Di-EGME) in aviation fuels.
- Water Reaction
To determine the presence of water-miscible components in aviation turbine fuels, and the effect of these components on volume change and on the fuel-water interface.
- Particulate Contamination
To gravimetrically determine the amount of particulate contaminant in a sample of aviation turbine fuel by filtration.
- Flash Point, Cleveland Open Cup
To determine the flash point and fire point of petroleum products by a manual Cleveland open cup apparatus.
- Metal Composition Analysis by EDXRF
To determine the elemental composition of materials in metal and liquid samples.
- Carbon Sulphur Determination
To determine carbon and sulphur elements in metal, cement, coal and soil samples.
- Cone Penetration
To measure the consistency of lubricating greases by the penetration of a cone of specified dimensions, mass, and finish.
- Water by Coulometric Karl Fisher
This test is for direct determination of water in the range of 10 to 25 000 mg/kg entrained water in petroleum products and hydrocarbons using automated instrumentation.
- Sound Noise Measurement
Measurement of noise in vehicles or generated from engines, exhaust and others. This test has been certified by the Malaysian Laboratory Accreditation Scheme (SAMM) which is the test of noise from in the vehicle and generated from the vehicle.
- Vibration Measurement
Whole-body Vibration and Hand-arm Vibration measurements resulting from vibration of seat and steering of vehicle.
- Floor Mounted Brake Tester
Measures the performance of indoor braking ability.
- Thermal Comfort
Measure heat stress ie human comfort over heat stress in vehicle or building space.
- Vibration Test By Vibration Analyzer
Vibration measurements on mechanical structures can be performed using this equipment. A component can be determined either in a defective condition or by using the vibration analysis method.
- Environmental Chamber
One room chamber that simulates test conditions against equipment or vehicles from -10°C + 80°C dan humidity range: 40 – 98%.
- Tilt Table
To determine vehicle stability during tilting in steep areas. Maximum weight test vehicle for this test is 25 tonnes.
Shaker is used to simulate or impose vibration on test equipment such as mechanical and electronic equipment. In addition, the simulation of vibration to the human body is also possible.
- Brake Tester
Measure braking perforamance easily in the field. Correlation between vehicle velocity, deceleration value, pedal force and braking distance can also be measured.
- Weighing Bridge
Measure the weight of the entire vehicle either by Gross Vehicle Weight or Payload.
For more detailed information, please contact:
Puan Zaliya binti Mohd Yusof
Telephone: 603-8732 4579